Site navigation
 
Department of Transport and Main Roads

Vehicle modification codes

The approved codes of practice can be found in the Queensland Road Vehicle Modification Handbook.

Light vehicle modification codes

The following modification codes are not used in Queensland:

Section LA—Engine

  • LA1: Equivalent engine installation
  • LA2: Performance engine installation
  • LA3: Supercharger and turbo charger installation
  • LA4: Engine modifications

Section LB—Transmissions

  • LB1: Transmission substitution
  • LB2: Rear axle substitution

Section LC—Vehicle controls

  • LC1: Dual-controls for driver trainer vehicles (design)
  • LC2: Dual-controls for driver trainer vehicles (modification)
  • LC3: Vehicle controls for persons with a disability (design)
  • LC4: Vehicle controls for persons with a disability (modification)

Find out more about these modifications in the QCOP.

Section LG—Brakes

  • LG1: Brake system conversion (design)
  • LG2: Brake system conversion section
  • LG3: Relocation of air brake components
  • LG4: Non-Standard brake system certification
  • LG5: Fitting of Auxiliary and Endurance Brakes
  • LG6: Fitting of air operated accessories
     

Section LH—Body and chassis

  • LH1: Roof conversion (design)
  • LH2: Roof conversion
  • LH3: Modified wheelbase conversion (design)
  • LH4: Modified wheelbase conversion
  • LH5: Vehicle construction (design)
  • LH6: Vehicle construction
  • LH7: Body/chassis variants conversion
  • LH9: Street rod certification (concessional)—find out more in the QCOP
  • LH10: Street rod certification (full)—find out more in the QCOP
  • LH11: Campervan, motorhome conversion section
  • LH13: Chassis Alteration (Design Certification)
  • LH14: Chassis Alteration (Modification Certification)

Section LK—Seating and occupant protection

  • LK1: Seat and seatbelt installation/removal
  • LK2: Seat and anchorage certification
  • LK3: Wheelchair Accessibility
  • LK6: Child restraint anchorage installation
  • LK8: Construction and installation of one-off roll-bars and roll-cages by individuals
  • LK9: Design and manufacture of commercial aftermarket roll-bars, roll-cages and other types of roll-over protection systems (ROPS)
  • LK10: Installation of aftermarket roll-bars, roll-cages and ROPS section

Section LL—Modifications to motorcycles

  • LL1: Modifications to motorcycle (LC) to motor tricycle (LEM1)

Section LM—Fuel systems

  • LM1: Fuel tank installation section

Section LO—Vehicle standards compliance

  • LO1: ADR compliance
  • LO2: ICV passenger cars and derivatives
  • LO3: Personally imported vehicle compliance
  • LO4: ICV LEM1 tricycle
  • LO5: ICV LEP1 tricycle
  • LO7: ICV motorcycle

Section LR- Installation of Vehicle Mounted Lifting System

  • LR1: Installation of Vehicle Mounted Lifting System

Section LS—Tyres, rims, suspension and steering

  • LS1: LHD vehicle steering conversion (design)
  • LS2: LHD vehicle steering conversion
  • LS3: Front suspension and steering modification (design)
  • LS4: Front suspension and steering modification
  • LS5: Rear suspension modification (design)
  • LS6: Rear suspension modification
  • LS9: High lift – up to 150mm (design certification)—find out more in the QCOP
  • LS10: High lift – up to 150mm modification certification—find out more in the QCOP
  • LS11: Gross vehicle mass re-rating—find out more in the QCOP
  • LS12: Light trailer modifications—find out more in the QCOP
  • LS14: Re-rating of Aggregate Trailer Mass (ATM)/Gross Trailer Mass (GTM) of a light trailer to manufacturer's specifications—find out more in the QCOP
  • LS15: Gross vehicle mass rating of light vehicles—find out more in the QCOP
  • LS16: Gross combination mass re-rating—find out more in the QCOP

Section LT—Test procedures

  • LT1: Beam and torsion tests
  • LT2: Lane change manoeuvre test
  • LT3: Exhaust emissions – IM240 test
  • LT4: Noise test

Section LV—Alternative power units

  • LV1: Installation of electric drives in motor vehicles

Section LX—TMR individual approval

  • LX1: Modification of light vehicles to the Department of Transport and Main Roads individual approval

Heavy vehicle modification codes

Heavy vehicle modification codes are only used to certify modifications to heavy vehicles.

Section A—Engine and ancillaries

  • A1: Engine substitution
  • A2: Air cleaner substitution or additional fitment
  • A3: Turbo charger installation
  • A4: Exhaust system alteration
  • A5: Road speed limiter installation

Section B—Transmission modification

  • B1: Transmission substitution of additional fitment

Section C—Tail shaft modification

  • C1: Tail shaft alterations

Section D—Rear axles

  • D1: Rear axle installation
  • D2: Differential substitution
  • D3: Fitting of non-standard rear wheel components

Section E—Front axle, steering wheels and tyres

  • E1: Front axle installation
  • E2: Steering alteration
  • E3: Fitting of non-standard front wheel components

Section F—Suspension modifications

  • F1: Suspension substitution
  • F2: Trailer suspension modifications

Section G—Brakes

  • G1: Relocation of air brake components
  • G2: Installation of trailer braking controls
  • G3: Trailer brake system upgrade
  • G4: Motor vehicle brake system certification
  • G5: Fitting of auxiliary and endurance brakes
  • G6: Fitting of air operated accessories
  • G7: Brake system substitution/wheelbase extension
  • G8: Trailer brake system upgrade (design)

Section H—Chassis

  • H1: Wheelbase extension outside OEM options
  • H2: Wheelbase reduction outside OEM options
  • H3: Wheelbase alterations within OEM
  • H4: Chassis alteration
  • H5: Trailer chassis modifications

Section J—Body mounting

  • J1: Body mounting
  • J2: Truck-bus body fitting
  • J3: Fitting of roll-over or falling object protection system
  • J4: Tipper bodies (design) 

Section K—Cabin

  • K1: Seating capacity alteration, seat, seatbelt and anchorage alteration
  • K2: Certification of seat and seatbelt anchorage
  • K3: Cabin conversions
  • K5: Installation of wheelchair occupant restraint system
  • K6: Child restraint anchorage installation

Section M—Fuel systems

  • M1: Fuel system alterations

Section P—Tow couplings

  • P1: Towbar and coupling installation other than fifth wheels and kingpins
  • P2: Fifth wheel and kingpin installation

Section R—Vehicle mounted lifting systems

  • R1: Installation of vehicle mounted lifting systems
  • R2: Wheelchair loader installation

Section S—Vehicle rating

  • S1: GVM/GCM re-rating (to S2 or S3 approved design or within manufacturer's specifications)
  • S2: GVM re-rating (design)
  • S3: GCM re-rating (design)
  • S4: GVM rating (rigid omnibus) (stand-alone Queensland code)
  • S5: GVM rating (articulated omnibus) (stand-alone Queensland code)
  • S6: Omnibus licencing evaluation (stand-alone Queensland code)
  • S7: ATM/GTM re-rating
  • S8: Motor vehicle road train rating
  • S9: Prime mover B-double rating
  • S10: Concessional livestock loading (stand-alone Queensland code)
  • S11: Road train trailer rating
  • S12: ATM/GTM re-rating (design)
  • S13: Bus life vehicle rating—find out more in the QCOP

Section T—Tow truck modification

  • T1: Tow trucks (construction)
  • T2: Tow trucks (design)
Last updated 10 May 2024